Our rubber ESD mats are dual-layer: static dissipative on the top, and conductive on the bottom.
Anti Static Wrist Straps Where to Connect
video-thumb-0
video-thumb-1
Our rubber ESD mats are dual-layer: static dissipative on the top, and conductive on the bottom.
Anti Static Wrist Straps Where to Connect
SKU: 5300 Category: Tags: , , , , , , , , , ,

• Customizable .08″ / 2mm thick anti static ESD mat rolls

• 2-layer static dissipative rubber matting pads tables and is required for ESD grounding in ANSI / ESD S20.20 compliant work areas for static control.

Prices

SizesQty 1-9Qty 10+
24" x 50'$443.78 USD$406.80 USD
30" x 50'$554.72 USD$508.49 USD
36" x 50'$665.66 USD$610.19 USD
48" x 50'$887.54 USD$813.57 USD






































Specs

► Meets ANSI / ESD STM 4.1 Standard using FTMS 101C Method 4046.

► Lead-Free. Recyclable. Meets European Union (EU) Restriction of Hazardous Substances Directive (RoHS) regulating the reuse of products used in electrical and electronic equipment.

PropertiesUnitsTypical aluesTest Method
Material-Nitrile Butadiene Rubber / Carbon-
ThicknessInches.08ASTM D-2103
ThicknessMillimetres2ASTM D-2103
Tensile Strength • Top Layerkg / sq. cm> 120ASTM D-412
Tensile Strength • Bottom Layerkg / sq. cm> 160ASTM D-412
Tear Strength • Top Layerkg / sq. cm> 90ASTM D-412
Tear Strength • Bottom Layerkg / sq. cm> 100ASTM D-412
Elongation • Top Layer%350ASTM D-412
Elongation • Bottom Layer%250ASTM D-412
Hardness • Top LayerShore A50ASTM D-2240
Hardness • Bottom LayerShore A60ASTM D-2240
Gravity • Top Layer-1.3ASTM D-792
Gravity • Bottom Layer-1.4ASTM D-792
ESD Surface Resistance • Top Layerohms / square< 109ASTM D-257
ESD Surface Resistance • Bottom Layerohms / square< 105ASTM D-257
Volume Resistivity • Top Layerohms / square< 108ASTM D-257
Volume Resistivity • Bottom Layerohms / square< 104ASTM D-257
Static Decayseconds< 0.01EIA-541
Temperature ToleranceFahrenheit / Celsius187F / 86C-

How to Cut an ESD Mat Roll Video

Transcript

In this video we are going to show you how to cut an ESD Mat Roll.

The Elimstat 5300 series ESD mat roll is made of an anti static rubber material that is 2mm thick. The top surface is static dissipative and the bottom surface is conductive.

To cut the 5300 Mat roll, fix the mat to a starting point. Roll out the mat to a desired length and remove the accompanying plastic cover.

Place a T-Square on the mat roll, aligning it to your desired length. Cut the mat along the T-Square, keeping the blade flush to ensure a consistent cut.

To complete setting up your mat, Elimstat offers the 4730 series-grounding snap.

ESD Grounding Snaps for an Anti Static Mat

To add the grounding snap, place a soft support pad under the mat. This protects the table from the metal prongs of the snap. Press the snap into the mat with the prong side down. Use a support, such as a screwdriver, to press the snap fully into the mat.

Once the snap is flush against the top of the mat, turn over the mat and bend the prongs so that they bend inwards, securing the snap into the mat.

Connect Grounding Cables to Mats

• The grounding cables should be common point grounds to connect wrist straps to your workstation or mat grounds to bond the roll separately onto the floor.

ESD Grounding Method for a Common Point Ground

ESD Grounding Method for a Mat Grounding Cable

The top anti static side of the mat collects static off of hands, feet, tools, and equipment laid on top of it at a static dissipative rate, (1 x 106 to 9 x 108 ohms / square).

The bottom of the mat then conducts static to ground at a conductive rate, (1 x 103 to 9 x 104 ohms / square).

ESD Resistance Chart for an Anti Static Mat

However, if the mat is laying on top of a bench or floor made of an insulating material (like wood tables) you will need to install snaps and connect the mat to an electrical outlet with a grounding cable.

ESD Grounding Method for an ESD Workstation

Multiple grounding cables can be attached to the same electrical outlet. They should not be “daisy-chained” together. Instead, directly connect the grounding cables to the electrical outlet.

Electrical outlets typically are the best path to ground the mat in any building because they follow the piping to the Earth’s electrical field underneath the building.

When connected to the electrical outlet, the mat is in electrical balance with the positive and negative charges of the building you are using it in.

ESD Workstation Setup Video

Transcript

In this video, we are going to show you how to set up your 5300 series ANSI / ESD compliant workstation.

First, roll out an ESD safe mat roll.

This is the Elimstat 5300 series two-ply static dissipative mat. It is a two-ply nitrile rubber material that is 2 millimeters thick. The top surface is static dissipative and the bottom surface is conductive.

S20.20 Compliant Setup for an ESD Workstation with Mat for Static Control

Next, remove the 4715 common point ground from the bag. Snap the common point ground onto the installed 10 millimeter snap.

ESD Grounding Method for a Common Point Ground

Once the female snap on the mat is connected to the male snap on the common point ground, connect the eyelet on the other end of the wire to an outlet or to earth ground.

To install the eyelet onto an outlet remove the outlet screw and attach the eyelet onto the outlet screw. Screw both back into the outlet, making sure both are secured tightly. This grounds the mat and any accessory plugged into the common point ground.

Lastly, remove the wrist strap set from the bag and connect it to one of the two banana receptacles in the common point ground.

Wrist straps directly capture static from your skin’s surface, protecting your ESD sensitive components.

ANSI / ESD S4.1 Test Data

The border line between conductive and static dissipative is 1 million ohms per square. This is also referred to as 1 meg ohm or 1 x 106 ohms.

ESD Resistance Chart for 5300 Series Anti Static Mats

To satisfy the ANSI / ESD S4.1 Worksurfaces – Resistance Measurements test standard the top static dissipative part of the mat was measured using resistance-to-groundable point and resistance point-to-point tests.

ANSI / ESD S4.1 guidelines at section 8.0 recommend resistance-to-groundable point (RTG) tests should find the top surface of grounded mats measure ESD resistance between 1 x 106 and 1 x 109 ohms.

Resistance point-to-point (also known as top-to-top or RTT) tests should measure the ESD resistance of the top surface of the mats at greater than or equal to 1 x 106 ohms.

As viewable in our diagrams, all 5300 Series mat samples were recorded within the acceptable range between 1 x 106 and 1 x 109 ohms, regardless of humidity, to meet the current S4.1 standard.

ESD Resistance Chart for Low Relative Humidity Test of 5300 Series Anti Static Mat

In our low relative humidity test, the sample with the least resistance measured 1.2 x 107 ohms.

The mat sample with the highest resistance measured 3.9 x 107 ohms / square.

ESD Resistance Chart for Moderate Relative Humidity Test of 5300 Series Anti Static Mat

In our moderate relative humidity test, the sample with the least resistance measured 1.0 x 107 ohms.

The mat sample with the highest resistance measured 9.8 x 107 ohms.

You may also like…