Conductive ESD Floor Mats Non Slipping
Elimstat.com Anti Static Floor Mats are diamond-plated and havea nitricell sponge base. Connect to a 4720 Series Mat Ground to electrically bond the mat.
Custom Size Anti Static Floor Mats are available from 9 feet wide to 75 feet long. Call 937-324-1100 for a quote over the phone or fill out the form below.
Conductive ESD Floor Mats Non Slipping
video-thumb-0
Elimstat.com Anti Static Floor Mats are diamond-plated and havea nitricell sponge base. Connect to a 4720 Series Mat Ground to electrically bond the mat.
Custom Size Anti Static Floor Mats are available from 9 feet wide to 75 feet long. Call 937-324-1100 for a quote over the phone or fill out the form below.
SKU: N/A Category: Tags: , , , , ,

Conductive Vinyl ESD Safe Anti-Fatigue Mats for Workstations.

• Foam Cushioned Nitricell Sponge Base with Beveled Edges for comfort while standing on top of it.
• For Custom Size Quotes Contact Us
• Does Not Include Mat Grounding Cable
• Snap Pre-Installed

Prices

SizesQty 1-9Qty 10+
2' x 3'$117.93 USD$108.86 USD
3' x 5'$271.73 USD$250.83 USD






Specs

PropertiesTypical Values
MaterialVinyl Surface with Nitricell Sponge Base
Thickness9/16 Inches
FlammabilityA Rating per MVSS 302
ColorBlack
Compression.415 inches at 35 PSI (ASTM D-575)
Tabor Abrasion1% Loss at 10,000 Cycles (Fed Std 191)
Temperature Range-10F to 130F
ESD Surface Resistance Top-to-Top (RTT) (S4.1)1 x 103 to 1 x 106
ESD Surface Resistance-to-Ground (RTG) (S4.1)2 x 103 to 2 x 106
Coefficient of Friction.68 Dry (ASTM F-1677)
ESD Rating (S7.1)1 x 103 to 1 x 106

Connecting Ground to Mat

The 15 foot grounding cable for the Mat Ground is static dissipative on the outside, and contains a 1 meg ohm resistor built into it on the inside to ensure static is transferred through the cable at a static dissipative rate.

Mat Grounds are Static Dissipative

To ground the Mat Ground connect it to an electrical outlet or conductive material with access to ground underneath your building.

Electrical outlets typically are the best ground in any building because they follow the piping to ground underneath the building.

To connect the Mat Ground to an electrical outlet screw the #10 Ring Terminal on the end of the cable into an electrical outlet. (The #10 Ring Terminal fits a standard US electrical outlet).

ESD Workstation Setup Video

Transcript

In this video, we are going to show you how to set up your 5300 series ANSI / ESD compliant workstation.

First, roll out an ESD safe mat roll.

This is the Elimstat 5300 series two-ply static dissipative mat. It is a two-ply nitrile rubber material that is 2 millimeters thick. The top surface is static dissipative and the bottom surface is conductive.

Next, remove the 4715 common point ground from the bag. Snap the common point ground onto the installed 10 millimeter snap.

Once the female snap on the mat is connected to the male snap on the common point ground, connect the eyelet on the other end of the wire to an outlet or to earth ground.

To install the eyelet onto an outlet remove the outlet screw and attach the eyelet onto the outlet screw. Screw both back into the outlet, making sure both are secured tightly. This grounds the mat and any accessory plugged into the common point ground.

Lastly, remove the wrist strap set from the bag and connect it to one of the two banana receptacles in the common point ground.

Wrist straps directly capture static from your skin’s surface, protecting your ESD sensitive components.

You may also like…