We use cookies to enhance your browsing experience, serve personalised ads or content, and analyse our traffic. By clicking "Accept All", you consent to our use of cookies.
Customise Consent Preferences
We use cookies to help you navigate efficiently and perform certain functions. You will find detailed information about all cookies under each consent category below.
The cookies that are categorised as "Necessary" are stored on your browser as they are essential for enabling the basic functionalities of the site. ...
Always Active
Necessary cookies are required to enable the basic features of this site, such as providing secure log-in or adjusting your consent preferences. These cookies do not store any personally identifiable data.
No cookies to display.
Functional cookies help perform certain functionalities like sharing the content of the website on social media platforms, collecting feedback, and other third-party features.
No cookies to display.
Analytical cookies are used to understand how visitors interact with the website. These cookies help provide information on metrics such as the number of visitors, bounce rate, traffic source, etc.
No cookies to display.
Performance cookies are used to understand and analyse the key performance indexes of the website which helps in delivering a better user experience for the visitors.
No cookies to display.
Advertisement cookies are used to provide visitors with customised advertisements based on the pages you visited previously and to analyse the effectiveness of the ad campaigns.
Polyester with Hypoallergenic Silver-Suffused Nylon
Thread Resistance
100 ohms (typical) 160 ohms (maximum)
Ground Contact
360 degrees around Wrist
Color
Blue
Wrist Strap Snap
4mm Stud Snap
Snap Release
1-5 lbs of Pressure
Wrist Strap Back Plate
Curved Surgical Grade Stainless Steel
Cord Length
6 foot and 12 foot options
Cord Material
Polished Polyurethane Coil Insulation
Cord Snap Type
4mm Socket Snap
Cord Plug Type
Swivel Type Plug with 6 leaves for Banana Jack
Cord Plug Alternative
Alligator Clip slides over Plug for Banana Jack
Cord Resistor
1 Meg Ohm Resistor Built Inside
Cord Diameter
2.5mm
Cord Flex Life
50,000 Flexes
ESD Workstation Setup Video
Transcript
In this video, we are going to show you how to set up your 5300 series ANSI / ESD compliant workstation.
First, roll out an ESD safe mat roll.
This is the Elimstat 5300 series two-ply static dissipative mat. It is a two-ply nitrile rubber material that is 2 millimeters thick. The top surface is static dissipative and the bottom surface is conductive.
Next, remove the 4715 common point ground from the bag. Snap the common point ground onto the installed 10 millimeter snap.
Once the female snap on the mat is connected to the male snap on the common point ground, connect the eyelet on the other end of the wire to an outlet or to earth ground.
To install the eyelet onto an outlet remove the outlet screw and attach the eyelet onto the outlet screw. Screw both back into the outlet, making sure both are secured tightly. This grounds the mat and any accessory plugged into the common point ground.
Lastly, remove the wrist strap set from the bag and connect it to one of the two banana receptacles in the common point ground.
Wrist straps directly capture static from your skin’s surface, protecting your ESD sensitive components.
Wrist Strap
Hypoallergenic silver-suffused nylon threading captures static directly from your skin’s surface at a conductive rate into a surgical grade stainless steel curved backplate.
A 4mm stud snap on the wrist strap is where the 4mm socket snap of the coil cord connects to it.
For optimal performance, make sure nothing (including an ESD Smock sleeve) gets between the wrist strap and the skin surface of the wearer.
Coil Cord
On the outside, the cord is made of polished polyurethane (PU) that is static dissipative.
On the inside, the encapsulated 1 meg ohm resistor ensures that electrons are transferred through the cord to ground at a static dissipative rate.
Static electrons collected off your body by the wrist strap are transferred to ground by attaching the coil cord to grounding:
Alternatively, you can clip the coil cord to a metal railing with the included alligator clip (which slides over the plug).
1 Meg Ohm Resistor
1 Meg Ohm = 1 x 106 Ohms
A 1 Meg Ohm Resistor is built into the coil cord to slow down an electrostatic discharge event (ESD) from a highly charged ungrounded surface from discharging instantaneously through the coil cord.
Typically a 1 Meg Ohm Resistor slows down an electrostatic discharge (ESD) a few more milliseconds than if it were not present.
Common Point Ground (SKU: 4715)
1 × $7.88 
