Prices
| Product | Qty 1-9 | Qty 10-99 | Qty 100+ |
|---|---|---|---|
| Anti Static Wristband Only | $2.22 USD | $2.02 USD | $1.85 USD |
| Anti Static Wristband and 6′ Coil Cord | $5.02 USD | $4.56 USD | $4.18 USD |
| Anti Static Wristband and 12′ Coil Cord | $6.16 USD | $5.60 USD | $5.13 USD |
• (1) Wristband captures static electrons directly from your body. Curved backplate.
• (1) Coil Cord (6 ft. or 12 ft.) carries static to ground. (1) Clip included: slides over cord plug if needed.
Specs
| Dimension | Quality |
|---|---|
| Fabric | Polyester with Hypoallergenic Silver-Suffused Nylon |
| Thread Resistance | 100 ohms (typical) 160 ohms (maximum) |
| Ground Contact | 360 degrees around Wrist |
| Color | Blue |
| Wrist Strap Snap | 4mm Stud Snap |
| Snap Release | 1-5 lbs of Pressure |
| Wrist Strap Back Plate | Curved Surgical Grade Stainless Steel |
| Cord Length | 6 foot and 12 foot options |
| Cord Material | Polished Polyurethane Coil Insulation |
| Cord Snap Type | 4mm Socket Snap |
| Cord Plug Type | Swivel Type Plug with 6 leaves for Banana Jack |
| Cord Plug Alternative | Alligator Clip slides over Plug for Banana Jack |
| Cord Resistor | 1 Meg Ohm Resistor Built Inside |
| Cord Diameter | 2.5mm |
| Cord Flex Life | 50,000 Flexes |
ESD Workstation Setup Video
Transcript
In this video, we are going to show you how to set up your 5300 series ANSI / ESD compliant workstation.
First, roll out an ESD safe mat roll.
This is the Elimstat 5300 series two-ply static dissipative mat. It is a two-ply nitrile rubber material that is 2 millimeters thick. The top surface is static dissipative and the bottom surface is conductive.
Next, remove the 4715 common point ground from the bag. Snap the common point ground onto the installed 10 millimeter snap.
Once the female snap on the mat is connected to the male snap on the common point ground, connect the eyelet on the other end of the wire to an outlet or to earth ground.
To install the eyelet onto an outlet remove the outlet screw and attach the eyelet onto the outlet screw. Screw both back into the outlet, making sure both are secured tightly. This grounds the mat and any accessory plugged into the common point ground.
Lastly, remove the wrist strap set from the bag and connect it to one of the two banana receptacles in the common point ground.
Wrist straps directly capture static from your skin’s surface, protecting your ESD sensitive components.
Wrist Strap
Hypoallergenic silver-suffused nylon threading captures static directly from your skin’s surface at a conductive rate into a surgical grade stainless steel curved backplate.
A 4mm stud snap on the wrist strap is where the 4mm socket snap of the coil cord connects to it.
For optimal performance, make sure nothing (including an ESD Smock sleeve) gets between the wrist strap and the skin surface of the wearer.
Coil Cord
On the outside, the cord is made of polished polyurethane (PU) that is static dissipative.
On the inside, the encapsulated 1 meg ohm resistor ensures that electrons are transferred through the cord to ground at a static dissipative rate.
Static electrons collected off your body by the wrist strap are transferred to ground by attaching the coil cord to grounding:
a wrist strap ground, or a common point ground.
Alternatively, you can clip the coil cord to a metal railing with the included alligator clip (which slides over the plug).
1 Meg Ohm Resistor
1 Meg Ohm = 1 x 106 Ohms
A 1 Meg Ohm Resistor is built into the coil cord to slow down an electrostatic discharge event (ESD) from a highly charged ungrounded surface from discharging instantaneously through the coil cord.
Typically a 1 Meg Ohm Resistor slows down an electrostatic discharge (ESD) a few more milliseconds than if it were not present.
You may also like…
-
5300 Series Anti Static Table Mat
Select options This product has multiple variants. The options may be chosen on the product page -
Common Point Ground
Add to cart -
Continuous Workstation Monitor
Add to cart
