Anti Static ESD Workstation Table Top Mats

How ESD Mats work with Continous Monitor

Color

Size

Clear

Antistatic Work Mats are installed with (2) two snaps on the corners of the long side to connect common point ground, wrist straps, and monitors (if desired) separately.

Prices

Sizes	Qty 1-9	Qty 10+
2' x 3'	$55.60 USD	$44.88 USD
2' x 4'	$68.30 USD	$54.64 USD
2' x 5'	$81.00 USD	$64.80 USD
2' x 6'	$93.70 USD	$74.96 USD
30" x 5' (Blue)	$96.88 USD	$77.50 USD
30" x 5' (Dark Blue, Gray, Green)	$115.67 USD	$101.97 USD

Specs

► Meets ANSI / ESD STM 4.1 Standard using FTMS 101C Method 4046.

► Lead-Free. Recyclable. Meets European Union (EU) Restriction of Hazardous Substances Directive (RoHS) regulating the reuse of products used in electrical and electronic equipment.

Properties	Units	Typical alues	Test Method
Material	-	Nitrile Butadiene Rubber / Carbon	-
Thickness	Inches	.08	ASTM D-2103
Thickness	Millimetres	2	ASTM D-2103
Tensile Strength • Top Layer	kg / sq. cm	> 120	ASTM D-412
Tensile Strength • Bottom Layer	kg / sq. cm	> 160	ASTM D-412
Tear Strength • Top Layer	kg / sq. cm	> 90	ASTM D-412
Tear Strength • Bottom Layer	kg / sq. cm	> 100	ASTM D-412
Elongation • Top Layer	%	350	ASTM D-412
Elongation • Bottom Layer	%	250	ASTM D-412
Hardness • Top Layer	Shore A	50	ASTM D-2240
Hardness • Bottom Layer	Shore A	60	ASTM D-2240
Gravity • Top Layer	-	1.3	ASTM D-792
Gravity • Bottom Layer	-	1.4	ASTM D-792
ESD Surface Resistance • Top Layer	ohms / square	< 10⁹	ASTM D-257
ESD Surface Resistance • Bottom Layer	ohms / square	< 10⁵	ASTM D-257
Volume Resistivity • Top Layer	ohms / square	< 10⁸	ASTM D-257
Volume Resistivity • Bottom Layer	ohms / square	< 10⁴	ASTM D-257
Static Decay	seconds	< 0.01	EIA-541
Temperature Tolerance	Fahrenheit / Celsius	187^F / 86^C	-

ANSI / ESD S4.1 Test Data

The border line between conductive and static dissipative is 1 million ohms per square. This is also referred to as 1 meg ohm or 1 x 10⁶ ohms / square.

ESD Resistance Chart for 5300 Series Anti Static Mats

To satisfy the ANSI / ESD S4.1 Worksurfaces – Resistance Measurements test standard the top static dissipative part of the mat was measured using resistance-to-groundable point and resistance point-to-point tests.

ANSI / ESD S4.1 guidelines at section 8.0 recommend resistance-to-groundable point (RTG) tests should find the top surface of grounded mats measure between 1 x 10⁶ and 1 x 10⁹ ohms / square.

Resistance point-to-point (also known as top-to-top or RTT) tests should measure the ESD resistance of the top surface of the mats at greater than or equal to 1 x 10⁶ ohms / square.

As viewable in our diagrams, all 5300 Series mat samples were recorded within the acceptable range between 1 x 10⁶ and 1 x 10⁹ ohms / square, regardless of humidity, to meet the current S4.1 standard.